Suspension Mods for the 2022+ WRX (VB)

Silver’s NEOMAX kit replaces the WRX VB’s factory dampers and springs with height-adjustable monotube coilovers. The SS2025 application is listed for 2022-on cars and uses 10K front and 10K rear springs, front camber plates, radial-bearing upper spring perc...

BC Racing’s BR Series replaces the WRX VB’s factory struts and springs with rebuildable monotube coilovers. The F-38-BR-RA application is listed for 2022–2026 cars and provides 30 clicks of combined compression/rebound adjustment, ride-height adjustment ind...

Eibach’s PRO-KIT E10-77-027-01-22 is a set of four progressive-rate springs for the 2022–2025 WRX 2.4T VB. It retains the factory dampers while lowering the car approximately 1.0 inch in front and 1.1 inches in the rear. The kit is intended for owners seeki...

Fortune Auto’s 500 Series replaces the factory struts and springs with rebuildable monotube coilovers built for street use and occasional track work. The WRX VB application uses 8K front and 8K rear springs, independent ride-height adjustment, adjustable da...

H&R Sport Spring kit 54471 replaces the WRX VB’s factory coil springs while retaining the original dampers. H&R specifies an approximate 1.1-inch front and 1.0-inch rear drop for 2022–2025 AWD WRX models, including GT and tS trims. The lower center of gravi...

Öhlins Road & Track kit SUS MX00S1 replaces the WRX VB’s factory dampers and springs with rebuildable DFV monotube coilovers for street and track use. Both axles use 90 N/mm springs, with 25-click one-way damping adjustment, independent preload and damper-l...

Racecomp Engineering’s Yellow Sport springs replace the factory coils while retaining the WRX VB’s original dampers. The set uses 360 lb/in front and 370 lb/in rear rates and lowers both axles approximately 25 mm. RCE developed the springs for the VB chassi...

SPC part 67660 replaces one factory rear lower control arm and provides on-car camber adjustment through an outboard cam. The high-strength stamped-steel arm uses SPC’s sealed xAxis joint and includes mounting hardware plus an offset bonded-rubber toe bushi...

Subaru 28313VC050 is the front-left steering knuckle used by Brembo-equipped WRX TR/tS applications and is a key mounting component when adapting the factory six-piston front brake geometry to another VB WRX. It is a side-specific suspension and hub carrier...

Subaru 28313VC040 is the front-right steering knuckle used by Brembo-equipped WRX TR/tS applications and is a key mounting component when adapting the factory six-piston front brake geometry to another VB WRX. It is a side-specific suspension and hub carrie...

Whiteline KTA216A replaces both factory rear lower control arms with adjustable stamped-steel assemblies. The pair uses cam-bolt and eccentric-bushing adjustment to provide approximately ±2.5 degrees of rear camber correction, useful after lowering when the...

COBB's CB-F51Z is a 24 mm solid front sway bar for the 2022-2026 WRX. Two end-link mounting positions let the installer choose between the available stiffness settings, while the supplied bushings replace the factory bar bushings. The bar is intended to red...

COBB's lowering springs for the VB WRX are a complete front and rear set (part CB-SUB009) designed as a direct replacement for the factory springs. They drop the car about 1.6 in. in front and 1.4 in. in the rear, which lowers the center of gravity, closes ...

Cusco part 6A2 540 A is the Type OS front strut-tower bar for the VB WRX. Its oval-section aluminum center bar joins vehicle-specific steel brackets at the upper strut towers, adding a rigid link across the engine bay without changing springs, dampers, or a...

PERRIN part PSP-SUS-565 clamps around the factory steering dampener to limit its rubber compliance rather than replacing the steering rack or changing alignment. The two black-anodized 6061-aluminum halves are intended to make steering inputs feel more imme...

Whiteline BSR57Z is a 22 mm solid rear sway bar developed for the 2022+ VB WRX. Three end-link mounting positions provide progressively higher roll stiffness; Whiteline describes effective settings near 21, 22, and 23 mm, allowing the owner to tune rear res...

AFD’s Sport Lowering Springs are aimed at owners who want a lower stance and tighter visual wheel gap while staying in the spring-only part of the suspension path. They make sense for daily-driven cars looking for a cleaner stance without stepping immediate...

Subaru Japan JDM STI Flexible Strut Tower Brace Front is an aftermarket component that reinforces the front strut towers. This brace is intended to reduce chassis flex for improved handling.

A'PEXi N1 Type ExV Damper Coilover Kit offers adjustable ride height and performance tuning for the 2022-2023 WRX. This kit combines robust design with high-performance features for improved driving experience.

Air Lift front kit is a suspension modification designed for the 2022-2023 Subaru WRX. It allows for adjustable ride height and improved handling characteristics.

Air Lift Performance Air Suspension Front Drop Kit allows for customizable ride height adjustments on the 2022-2023 WRX. This kit features air springs for enhanced comfort and significant drop capability.

Air Lift Performance air suspension front kit provides adjustable ride height for the Subaru WRX. This kit is designed to enhance the vehicle's suspension performance.

Air Lift Performance rear air suspension kit is engineered for the WRX and other models. This kit provides adjustable ride height and improved handling capabilities.